Novelty: COB LED-Strip - no LEDs visible - 1,300 lm/m - 2,700K warm white - IP67 5m roll

€92.50*

Content: 5 (€18.50* / 1 Meter)

Available, delivery time 3-5 days

Colour temperature
Water protection
Product number: LK04-32c-25
Available stock: 17

LED type: COB - no single LEDs visible
Beam angle: 120°
Brightness: 1,300 lm/m
Color rendering: High CRI>90
Voltage: 24 Volt
Power: 14 Watt/m

Price for 1 roll = 5 meters -Buy by the meter -



New type of LED tape where no individual LEDs are visible! A continuous bright, uniform light band is created. 

This has advantages for various applications:

  • Homogeneous line light, even in very flat aluminum profiles.
  • Continuous, narrow accent or orientation light
  • Absolutely uniform indirect lighting at very short distances

The COB LED-Strips are also very efficient - approx. 100 lumens / watt - and can be processed just as flexibly as normal LED strips. Short pitch distances (only 4.5cm) allow the adjustment to desired dimensions and due to the double-sided adhesive tape on the back, the COB LED-Strips are very easy to install. 

The continuous light effect without visible individual LEDs in the COB LED-Strip is achieved by a new process. With white LEDs, the light has always been generated by a converting phosphor layer. Now, instead of applying a separate, tiny phosphor layer to each LED chip - as it is usually the case - COB LED-Strips cover the entire 5m strip in one piece with a continuous phosphor. The result is a uniformly homogeneous band of light, as in color, so in brightness.


 

Available Variants

  • 5m-roll IP20 without water protection, incl. 10cm connection cable
  • 5m-roll IP67 water protection in silicone tube, incl. 10cm connection cable

Furthermore, the LED tape is sold by meter IP20 in 1 - 30m length.

All variants have a 3M adhesive tape on the back for mounting, can be divided every 4.5cm and are available in various color temperatures (e.g. 3.000K warm white).

 


 

Notes on accessories:

To operate 5m (1 roll) of LED strips, a 24V power supply with min. 75 Watt is required. 5m x 14W/m = 70 Watt.

https://shop.led-studien.de/de/zubehor/netzteile/24v-netzteile

For brightness controll of 5m a controller with min. 3,2 Ampere is needed. 75W / 24V = 3,2 Ampere.

https://shop.led-studien.de/de/controller/dimmer-1-2-kanal


 

Frequently asked questions:

 

Can COB LED-Strips be used like normal LED Strips?

Yes. COB-LED-Strips can be laid, cut and connected just as flexibly as normal LED-Strips. The solder contacts for connecting cables are also exposed.

 

What is the height of the COB LED-Strips?

Only 1.5mm. COB LED-Strips are not significantly higher than normal LED strips and therefore fit, for example, in all standard aluminum profiles. The IP67 versions have the typical height of 4mm due to the surrounding silicone tube.

 

Does the phosphor coating reduce the lifetime of the LEDs?

No. COB technology has been used for many years in numerous high-power LED modules (up to 100 Watt output), where the temperature input into the phosphor coating is immensely high. There is no known reduction in lifetime here.

 

Are COB-LED-Stips water-protected, e.g. suitable for outdoor use?

For this purpose, choose the variants with IP67 water protection.

 

You can find more answers to frequently asked questions about LED strips in our FAQ.


 

Properties "Novelty: COB LED-Strip - no LEDs visible - 1,300 lm/m - 2,700K warm white - IP67 5m roll"
Brightness lm/m: 1300
Colour rendering: CRI>90
Colour temperature: 2.700K warm
Energy efficiency class (EEK): F
Power: 15
Seperatable every (cm): 4,5 cm
Strip width in mm: 10
Voltage: 24V
Water protection: IP67 with silicon tube
LED/m: 528, COB
Data according to manufacturer. Errors and changes reserved.
datasheet

Power Supply

Power supply HLG 24V - 5A - 120 Watt, extremely quiet
Switching power supply Meanwell HLG-120-24, 24 Volt, 5 Ampere, 120W Overload protection by current limitation, auto recovery protected against short circuit, overload, overvoltage built-in PFC circuit for indoor and outdoor use (IP65) adjustable output voltage adjustable current limitation Technical data:  Model HLG-120-24  Voltage 24V  Maximum power 120W  Current 5A  Adjustable voltage range 22 ~ 27V  Overcurrent protection 95...108%  Inrush current, max. 65A  Voltage input 90...264V AC (47...63Hz), 127...370V DC  Power factor 0,95  Working temperature -40...+70°C  Dimensions 2220x68x38.8mm (LxWxH)  Weight 1,120g  
Product number: LED1134

€49.00*

Recommended Drivers

Radio dimmer LK55-2 | 1 x 8A
The 1 x 8 amp driver offers only one output and is therefore only suitable as a dimmer. Due to the 8 amps, however, very powerful LED components can be connected. At 24 volts, for example, LED components up to 170 watts are possible. The driver is installed between the power supply and the LED component. It is ideally suited for small and medium installations, as well as a supplement for larger installations. The driver belongs to the LK55 series and can be combined with all dimmer remote controls available there.    NOTES: All drivers of our LK55 series remember the last setting even in case of power loss. RGBW and CCT color temperature remote controllers have no function on the LK55-2 LED dimmer.   Technical data: Voltage: 12V-36V DCPower: Power connection via external switching power supply (not included)Load: 1 x 8A Min. dim level: <1% (for RGB/W <3%)Connection: input: V+/ground, push button; output: V+/groundIP class: IP 20 Dimensions: LxWxH 95x37x20mm   Operation via pushbutton input The LK55-2 offers 2 green screw terminals on the back for a button input. For example, a simple pushbutton can be connected to this and thus control the light without radio. Short keystroke switches the LEDs on and off. Long keystroke dims the LEDs up and down. Instead of a pushbutton, in principle only 2 cables can be connected, which are then held together short or long. Video tutorial for dimming via radio   Video tutorial for dimming via cable with PUSH DIM
Product number: LK55-2

€36.00*

Suitable Radio Control for Drivers

Remote control with rotary knob | wall mounting
for 1-channel receivers of the LK55 series Controllable zones: 1 Battery operation: 3V DC, CR2025 All remote controls can operate all drivers / receivers of the LK55 series and, if required, also the WiFi driver LK35. It is also possible for several remote controls to operate one driver. E.g. a handheld remote control and an additional wireless wall panel or several wireless wall panels at different positions in the room. If required, up to 8 remote controls can operate 1 driver. The range of the radio signal is up to 30m. Visual contact is not necessary. Solid walls made of concrete, brick or similar naturally weaken the radio signal. Power supply: Note that some models are powered by a battery (coin cell) that must be replaced every 1-2 years. This applies to all pushbutton and potentiometer models. All models with touch field can be supplied via the 230V house network, so that no battery change is required.   Combination with switch series of well-known manufacturers The housing frame of the controls measures 86x86mm with a depth of 12mm. In case you want to combine the wall control with light switches, sockets etc., the following switch series are similar in design and dimensions: MERTEN M-Plan GIRA E2 (flat installation) JUNG Serie A Creation KOPP HK i8 ROHDE+ROHDE Check the exact dimensions directly with the manufacturers. NOTICE:  The LK55 remote control for pure dimming should not be used in combination with CCT LED strips (adjustable color temperature) or RGBW LED strips, but only for pure white LED strips with fixed color temperature. Background: When dimming via you would lose all color settings here, because the LED drivers drive all outputs (RGBW or WW/KW) down or up identically. Instead, dim via the appropriate CCT or RGBW remote controls. Technical data:  Item no. LK55W  Power supply 110-240VAC  Dimensions (BxWxD) 86x86x12mm, Installation depth: 20mm  
Product number: LK55Wmas

€34.00*
Remote control with button | wall mounting
Pushbutton/dimmer for wall mounting or, thanks to the ultra-flat design, directly for gluing or screwing onto the wall. for universal controller of the LK55 series Controllable zones: 1 Power supply: 3V CR2430 battery Use in a standard switch series Since the stylus uses the standardized 55mm dimension (55x55mm), another frame can also be used. The central pushbutton can be removed and inserted into the frame of a known switch series, e.g. JUNG AS 500, MERTEN M, GIRA System 55 or GIRA E2. All major manufacturers have switch series in their program that fit the 55 standard dimension. LK55 series All remote controls can operate all drivers / receivers of the LK55 series and, if required, also the WiFi driver LK35. It is also possible for several remote controls to operate one driver. E.g. a handheld remote control and an additional wireless wall panel or several wireless wall panels at different positions in the room. If required, up to 8 remote controls can operate 1 driver. The range of the radio signal is up to 30m. Visual contact is not necessary. Solid walls made of concrete, brick or similar naturally weaken the radio signal. NOTICE:  The LK55 remote control for pure dimming should not be used in combination with CCT LED strips (adjustable color temperature) or RGBW LED strips, but only for pure white LED strips with fixed color temperature. Background: When dimming via you would lose all color settings here, because the LED drivers drive all outputs (RGBW or WW/KW) down or up identically. Instead, dim via the appropriate CCT or RGBW remote controls.   Technical data:  Item no. LK55K  Power supply 3V CR2430 batteries  Dimensions (BxWxD) 86x86, Installation depth: 13mm   Installation: Compatible with JUNG AS 500, GIRA System 55, GIRA E2 and many other switch series.
Product number: LK55Kmas

€39.00*
Handheld remote control touch wheel | 4 zones
Brightness control up to 4 light zones operateable Touch wheel for adjusting the brightness 1 Channel 3 memory keys for individual settings All remote controls can operate all drivers / receivers of the LK55 series and, if required, also the WiFi driver LK35. It is also possible for several remote controls to operate one driver. E.g. a handheld remote control and an additional wireless wall panel or several wireless wall panels at different positions in the room. If required, up to 8 remote controls can operate 1 driver. NOTICE:  The LK55 remote control for pure dimming should not be used in combination with CCT LED strips (adjustable color temperature) or RGBW LED strips, but only for pure white LED strips with fixed color temperature. Background: When dimming via you would lose all color settings here, because the LED drivers drive all outputs (RGBW or WW/KW) down or up identically. Instead, dim via the appropriate CCT or RGBW remote controls.   Technical data:  Item no. LK55FB1  Power supply 3 x 1,5V AAA batteries  Dimensions (LxWxH) 120x55x17mm   Operation:   This video explains the functions of the LK55FB1:  
Product number: LK55FB1

€49.00*

Suitable Accessories for IP67

Silicone end cap: 10mm
Suitable silicone can be ordered separately.
Product number: SAK10

€0.30*
Silicone: 10ml
Mit der Silikondichtmasse lassen sich Neonflex- oder LED-Streifen im Silikonschlauch (IP67/68) mit entsprechenden Endkappen wieder wasserdicht verschließen. Dies ist vor allem nützlich, wenn eine Rolle in mehrere Teilstücke aufgeteilt werden soll. Das Silikon ist acetatfrei wodurch beim Aushärten keine Essigsäure entsteht, welche die elektronischen Bauteile des LED-Bandes beschädigt. Eine Tube á 10ml reicht zum Versiegeln von ca. 4-6 Endkappen (je nach Größe der Endkappe).
Product number: SIL01

€2.50*
Waterprotected cable set: 2-pin
Das Set erlaubt es in Verbindung mit Silikondichtmasse und Endkappen wasserdichte Anschlüsse für weiße LED-Streifen herzustellen. Dies ist vor allem nützlich, wenn eine Rolle in mehrere Stücke geteilt werden soll.
Product number: LK04-23d-Con2

€2.50*