LED tape digital WS2811 - RGB LEDs - 12V

The SEDUv3 is a universal driver for digital LED pixels. It can be used to control an ambient light system as well as for an LED matrix. In contrast to the SEDUv2 additional pixels like the WS2811/12 or MY9221 are supported. The firmware is still being extended to support even more pixel types. In addition, it is possible to choose between different input protocols within one firmware. Supported are: miniDMX tpm2 DMX (future) tpm2.net / Artnet in connection with WLAN Up to 3000 pixels WS2801 and 1024 pixels WS2811/12 are supported. With a µSD card created sequences can be played back offline. You can switch between the programs with a button (in the future also via IR remote control). Scope of delivery: 1x SEDU board v3 according to version 1x connector data port Technical data: Parameter Value Power supply: 5V DC via µUSB port,max. current consumption approx. 300mA Housing: Aluminum housing, screwed Dimensions: 105 x 50 x 28 mm Data sheet / Downloads  SEDU-Board Downloads

The LK142 Staircase Effect Controller allows the control of staircase lighting from 8 - 32 steps. It offers a total of 32 outputs, e.g. for LED strips or profiles in the range of 5-24VDC, 1A. For example, our standard LED strips as well as the new free-cut COB LED strips can be controlled flexibly. Controlled by pushbuttons or motion detectors above and below the stairs, the steps can be illuminated step by step with great effect. Depending on the activation, the effect runs from bottom to top or from top to bottom. In addition, digital pixel LEDs can be integrated for a running light, e.g. in the handrail. Various effect modes and speed settings allow for flexible adjustment of the staircase effect.Benefits at a glance: Selective control of 8-32 steps with 5-24VDC, 1A Additional chaser effect, e.g. in the handrail, via pixel LED strips (12 color modes) 4 effect modes, 8 speeds Triggered by PIR motion sensors or push-buttons above and below the stairs Daylight sensor for twilight switching 2 controllers can be cascaded for large staircases with up to 64 steps Wiring diagram: Scope of delivery:Staircase effect controller 2 x PIR sensor 2 x extension cable (5m) for PIR sensor 1 x twilight sensor Technical data: Item-Nr. LK142 Output ports 32 x 5-24VDC, 1A step illumination2 x SPI pixel for running light Adressable pixel Up to 960 pixel Adressable pixel types WS2801, 2803, 2811, 2812, 2813, 2815TM1804, 1809, 1812, 1829, 1914AUCS1903, 1909, 1912, 2903, 2909, 2912UCS5909, 6912LPD6803, 1101, 8803, 8806GS8206, 8208GW6205P9813SK9822 Powersupply  5 - 24VDC (via ext. powersupply) Input ports2 x 5-24VDC voltage input2 x PIR motionsensor 2 x pushbutton (+ cascade option)1 x daylight sensor IP protection IP20 Dimensions L186×W86×H26(mm) Weight 520g

ArtNet to DMX decoder for a total of 8 DMX universes (max. 4096 DMX channels) in 19" rack housing (1U). Robust construction. PushDial and OLED display for setting IP addressing, port assignment and for test functions.Perfect synchronization between the individual universes, e.g. for pixel mapping and voxel mapping. The Artnet controller is ready for use within seconds after commissioning. One HTP merge is automatically available for two Art-Net sources. If required, you can access and change specific device settings via the integrated web configuration tool. Technical data: Item no. LK131 Input ports 1 x Ethernet IN (RJ45) Output ports 8 x DMX OUT (XLR 5pin), 1 x Ethernet THRU Voltage input  230VAC (AC cable included) Dimensions 19" rack housing (1U) Weight 1.5kg

ArtNet to DMX decoder for a total of 16 DMX universes (max. 8192 DMX channels) in 19" rack housing (1U). Robust construction. PushDial and OLED display for setting IP addressing, port assignment and for test functions.Perfect synchronization between the individual universes, e.g. for pixel mapping and voxel mapping. The Artnet controller is ready for use within seconds after commissioning. One HTP merge is automatically available for two Art-Net sources. If required, you can access and change specific device settings via the integrated web configuration tool. Technical data: Item no. LK132 Input ports 1 x Ethernet IN (RJ45) Output ports 16 x DMX OUT (RJ45), 1 x Ethernet THRU Voltage input  230VAC (AC cable included) Dimensions 19" rack housing (1U) Weight 1.5kg

The drivers for digital LED strips are specially designed to control as many RGB pixels as possible individually.With the LK99, up to 2,720 pixels are possible, divided into 4 channels with 680 RGB pixels each. This corresponds to a total of 16 DMX universes, which are transmitted via LAN/ArtNet. The 4 pixel outputs can be loaded with max. 7 amps per channel. For larger installations, the pixels can and should be powered separately. The controller then supplies only the data signal (DATA). Pixels with and without CLOCK signal (CLK) can be controlled. Pixel types with CLK are e.g. WS2801 or APA102. The controller can be controlled via ArtNet and offers an additional DMX-OUT port with 512 channels on the output side. For configuration, the controller has an integrated web interface as an alternative to direct input on the display. The configuration options are very extensive: selection of pixel type and color sequence (RGB, RGB, GRB etc.) flexible addressing (DMX-Universe and start address individually for each of the 4 outputs) number of pixels to control per channel (0-680 pixels - e.g. to save DMX universes) number of zero pixels to skip first unused pixels in an installation Zig-zag or backward addressing of pixels for matrix applications Brightness limitation per channel In addition, the controller offers a test mode to test the installation with various effects (Chase, Dots, Rainbow, ...) and static programs (all pixels red, all pixels white, ...) even without an applied ArtNet signal. The speed of the effects can be varied. Technical data: Item no. LK99 Output spots 4 x 7 Ampere (Multi SPI) Controllable pixels 4 x 680 = 2,720 Controllable ICs WS2801, 2803, 2811, 2812, 2813, 2815 SK6812 (RGBW) TM1803, 1804, 1809, 1812, 1814 (RGBW) UCS1903, 1909, 1912, 2903, 2909, 2912, 5603UCS6909, 6912 9812, 2904 (RGBW), 8904 (RGBW)LPD6803, 1101, 8803, 8806 TLS3001, 3002 APA102 P9813 Voltage input  5 - 24VDC DMX outputs 1 x 512 Channels Dimensions L166×W110×H31(mm) Weight 510g

The drivers for digital LED strips are specially designed to control as many RGB pixels as possible individually.  With the LK63, up to 5.440 pixels are possible, divided into 16 channels with 340 RGB pixels each. This corresponds to a total of 32 DMX universes, which are transmitted via LAN/ArtNet.  The 16 pixel outputs can be loaded with max. 3 amps per channel. For larger installations, the pixels can and should be powered separately. The controller then supplies only the data signal (DATA).  Pixels with and without CLOCK signal (CLK) can be controlled. Pixel types with CLK are e.g. WS2801 or APA102.  The controller can be controlled via ArtNet and offers 2 additional DMX-OUT ports with 512 channels each. For configuration, the controller has an integrated web interface as an alternative to direct input on the display.  The configuration options are very extensive:  selection of pixel type and color sequence (RGB, RGB, GRB etc.)  flexible addressing (DMX-Universe and start address individually for each of the 4 outputs) number of pixels to control per channel (0-340 pixels - e.g. to save DMX universes)  number of zero pixels to skip first unused pixels in an installation  Zig-zag or backward addressing of pixels for matrix applications  Brightness limitation per channel  In addition, the controller offers a test mode to test the installation with various effects (Chase, Dots, Rainbow, ...) and static programs (all pixels red, all pixels white, ...) even without an applied ArtNet signal. The speed of the effects can be varied. Technical data: Item no. LK63 Output spots 16 x 3 Ampere (Multi SPI) Controllable pixels 16 x 340 = 5,440 Controllable ICs WS2801, 2803, 2811, 2812, 2813, 2815 SK6812 (RGBW) TM1803, 1804, 1809, 1812, 1814 (RGBW) UCS1903, 1909, 1912, 2903, 2909, 2912, 5603UCS6909, 6912 9812, 2904 (RGBW), 8904 (RGBW)LPD6803, 1101, 8803, 8806 TLS3001, 3002 APA102 P9813 Voltage input  5 - 24VDC DMX outputs 2 x 512 Channels Dimensions L258×W145×H41(mm) Weight 1,100g

Meanwell switching power supply HLG-240, 12V / 16A / 192W Overload protection by current limitation, auto recovery protected against short circuit, overload, overvoltage built-in PFC circuit for indoor and outdoor use (IP65) adjustable output voltage adjustable current limitation Note on the connection of LED drivers The HLG-240-12 offers a lot of power and therefore a high current of up to 12.5 amps. If possible, use both voltage inputs on all drivers with dual voltage inputs (++--). All larger drivers usually have dual voltage inputs. It is best to order two 3-way WAGO distributors so that you can split the +/- output cables of the HLG-150 into 2 cables each, which you then run in parallel to the driver inputs. Alternatively, you can use a driver Y-connection cable in combination with luster terminals. Technical data:  Model HLG-240-12  Voltage 12V  Maximum power 192W  Current 16A  Adjustable voltage range 6 ~ 12V  Overcurrent protection 95...108%  Inrush current, max. 75A  Voltage input 90...264V AC (47...63Hz), 127...370V DC  Power factor 0,95  Working temperature -40...+70°C  Dimensions 244.2x68x38.8mm (LxWxH)  Weight 1,300g