Customised assembly
High-quality technology
Engineering know-how

LED tape digital WS2815 - RGB-Pixel - IP20 - 12V

€79.00*

Content: 5 Meter (€15.80* / 1 Meter)

Available, delivery time: 3-5 days

LED dense
Product number: LK119-72
Available stock: 32

Pixel LED strips with 12V supply voltage are especially suitable for larger installations over several meters. While normal pixel LED strips with 5V require a new voltage supply every 2m at the latest due to the intensive voltage drop, with 12V strips 5m can also be realized without a new supply. 

In contrast to other 12V pixel solutions, with the WS2815 each LED is also a separately controllable pixel. So narrow resolutions with e.g. 30, 60, 72, 96 or even 144 pixels/m can be realized.

Another advantage of the WS2815 is that the data line is doubled. This leads to a significantly increased reliability. If one pixel fails, the following pixels remain unaffected. Furthermore, the WS2815 offers a comparatively high PWM frequency of 1,200Hz, which reduces flickering effects. 

WS2815 are compatible to the widely used WS2811 protocol (also WS2812) and therefore controllable with very many pixel controllers. For very large installations there are corresponding ArtNet Pixel drivers with up to 16 or even 32 DMX universes.

Delivery unit: one roll 5m


 

Technical data:

Item no. LK119-72
IC type WS2815 (SK6813 or similar)
Single colors 620-630nm red
510-525nm green
455-470nm blue
LEDs/m 72 - type 5050
Pixel/m 72
Width 10mm
divisible every 1.4cm
Voltage range 12V
Current/m 1.08A
Power consumption 13W/m
Luminous flux 312lm/m
PWM frequency 1,200Hz
Water protection IP20

 

Properties "LED tape digital WS2815 - RGB-Pixel - IP20 - 12V"
IP protection: IP20
Pixel/m: 72
Seperatable every (cm): 1,4 cm
Strip width in mm: 10
Voltage: 12V
LED/m: 72
Data according to manufacturer. Errors and changes reserved.

Recommended driver

Artnet LED Pixel driver for up to 5,440 pixels
The drivers for digital LED strips are specially designed to control as many RGB pixels as possible individually.  With the LK63, up to 5.440 pixels are possible, divided into 16 channels with 340 RGB pixels each. This corresponds to a total of 32 DMX universes, which are transmitted via LAN/ArtNet.  The 16 pixel outputs can be loaded with max. 3 amps per channel. For larger installations, the pixels can and should be powered separately. The controller then supplies only the data signal (DATA).  Pixels with and without CLOCK signal (CLK) can be controlled. Pixel types with CLK are e.g. WS2801 or APA102.  The controller can be controlled via ArtNet and offers 2 additional DMX-OUT ports with 512 channels each. For configuration, the controller has an integrated web interface as an alternative to direct input on the display.  The configuration options are very extensive:  selection of pixel type and color sequence (RGB, RGB, GRB etc.)  flexible addressing (DMX-Universe and start address individually for each of the 4 outputs) number of pixels to control per channel (0-340 pixels - e.g. to save DMX universes)  number of zero pixels to skip first unused pixels in an installation  Zig-zag or backward addressing of pixels for matrix applications  Brightness limitation per channel  In addition, the controller offers a test mode to test the installation with various effects (Chase, Dots, Rainbow, ...) and static programs (all pixels red, all pixels white, ...) even without an applied ArtNet signal. The speed of the effects can be varied. Technical data: Item no. LK63 Output spots 16 x 3 Ampere (Multi SPI) Controllable pixels 16 x 340 = 5,440 Controllable ICs WS2801, 2803, 2811, 2812, 2813, 2815 SK6812 (RGBW) TM1803, 1804, 1809, 1812, 1814 (RGBW) UCS1903, 1909, 1912, 2903, 2909, 2912, 5603UCS6909, 6912 9812, 2904 (RGBW), 8904 (RGBW)LPD6803, 1101, 8803, 8806 TLS3001, 3002 APA102 P9813 Voltage input  5 - 24VDC DMX outputs 2 x 512 Channels Dimensions L258×W145×H41(mm) Weight 1,100g
Product number: LK63

€400.00*
SP108E LED Pixel Controller with App control
The SP108 can drive up to 2,048 pixels and many different pixel types: WS2801, WS2811, WS2812, SK6812, APA102 and many more. The suitable app "LED Shop" is available for free for IOS and Android and offers 180 different chase effects as well as precisely adjustable single colors. Speed and brightness can be changed at any time. A handy feature is that you can choose your favorites from the 180 effects and then quickly select them. Setting up the driver is quite intuitive and done in a few minutes. The driver works in the 2.4 GHz WLAN and can be accessed directly via the smartphone as well as integrated into the home WLAN. Screenshots of the App: The scope of delivery includes: 1 x LED driver SP108E 1 x 3-pin connection cable for LED strips 1 x mini screwdriver Supported LED types: WS2801, WS2811, WS2812 SK6812, SK6812_RGBW, SK9822 APA102, APA105 TM1804, TM1814, TM1913, TM1914, TX1812, TX1813 LPD6803, LPD8806  P9813, P943S, P9411, P9412, P9413, P9414 GS8206, GS8208 SM16703, UCS1903, INK1003, DMX512 FAQ: Does the driver require an existing WLAN? No, the driver can also be controlled directly with the smartphone (AP mode) and offers its own WLAN access point ("SP108E_xxx") for this purpose. If a WLAN is available, the driver can alternatively be integrated into it (STA mode), so that the WLAN does not always have to be changed to operate the driver. Can multiple drivers be used simultaneously in the app? Yes, the app can manage multiple drivers at the same time. You can switch between the drivers and change the settings for each. In addition, the individual drivers can be switched on and off directly. However, there is no direct synchronization and each driver must be set accordingly for itself.  Does the app have to be active for the animations to run? No. The app is only needed for the setup. You can close the app afterwards and also turn off the smartphone, for example. The SP108 will continue to play effects. Does the driver keep its settings when it no longer receives power? Yes, the driver can simply be disconnected from the mains. When power is applied again, it will start with the previously set animation. All settings will be kept. How can the white LEDs be used, e.g. with a SK6812_RGBW? The app has a separate control for white LEDs (e.g. for SK6812_RGBW pixel strips). This can be used to set the proportion of white LEDs and then, in the case of effects, the white LEDs are taken into account accordingly, so that the colors are generally desaturated. In the effects section of the app, the SOLID setting can then also be used to activate a permanently white, high-quality light, e.g. for lighting tasks, if required. Can the SP108 also control LED matrices? A number of pixels and a number of segments can be set in the setup. For example, for an 8 x 8 matrix then 8 pixels and 8 segments. This is taken into account in the effects, but in most matrices the pixels are connected in a snake shape as a long line and this is unfortunately not taken into account by the SP108. Therefore the effects are not displayed as desired on the matrix, but every 2nd row of the matrix shows the effect quasi upside down. We hope for a technical improvement here soon. Technical data: Input: 5-24V DC, GND Output: VCC, GND, Data, Clock current consumption: approx. 90mA up to 2.048 pixels depending on IC type ambient temperature: -20°C - +60°C dimensions: 80x41x20mm Weight: 40g
Product number: LK126

€29.00*

Suitable aluminum profiles

2m LED top profile PN4 wide (for 2 parallel LED strips)
Choose your required accessories for the aluminum profile. E.g. a suitable cover, as well as end caps and/or retaining clips for mounting. You can also reorder only accessories here (such as retaining clips) by clicking away the preselection in the profiles and covers. Other mounting options and accessories for line lights If you want to realize long line lights, pendant lights or a hidden cable routing with this profile, choose the matching mounting rail PL10 with corresponding accessories. The mounting rail is available in silver, black & white. Further are available: Rail connectors straight and angled Cable suspensions Mounting springs for fastening in drywall Technical data: Width: 26.8 mm Height: 11,7 mm Width inside for LED strips: 24.1 mm 
Product number: AL29bund

€28.80*
2m LED-Micro-profile PL1
Choose your required accessories for the aluminum profile. E.g. a suitable cover, as well as end caps and/or retaining clips for mounting. You can also reorder only accessories here (such as retaining clips) by clicking away the preselection in the profiles and covers. Other mounting options and accessories for line lights If you want to realize long line lights, pendant lights or a hidden cable routing with this profile, choose the matching mounting rail PL10 with corresponding accessories. The mounting rail is available in silver, black & white. Further are available: Rail connectors straight and angled Cable suspensions Mounting springs for fastening in drywall Technical data: Width: 16.8 mm Height: 6 mm Width inside for LED strips: 12.4 mm 
Product number: AL21bund

€15.40*
2m LED-Top-profile PL2
Choose your required accessories for the aluminum profile. E.g. a suitable cover, as well as end caps and/or retaining clips for mounting. You can also reorder only accessories here (such as retaining clips) by clicking away the preselection in the profiles and covers. Other mounting options and accessories for line lights If you want to realize long line lights, pendant lights or a hidden cable routing with this profile, choose the matching mounting rail PL10 with corresponding accessories. The mounting rail is available in silver, black & white. Further are available: Rail connectors straight and angled Cable suspensions Mounting springs for fastening in drywall Technical data: Width: 16.8 mm Height: 13.1 mm Width inside for LED strips: 12.4 mm 
Product number: AL24bund

€17.00*