Digital white COB LED strip WS2811 - 24V - 36 Pixel/m | 6000K cool white
€65.00*
Content:
5 Meter
(€13.00* / 1 Meter)
Available, delivery time: 3-5 days
Product number:
LK147-60
Available stock:
11
- LED Typ: WS2811 - white
- 360 COB LED/m
- 36 Pixel/m (= 10 COB LED per Pixel)
- Voltage: 24Volt
- Brightness: 700lm/m
- Power: 11 Watt/m
- Width: 10mm
Price for 1 roll = 5m
The digital white COB LED strips are available in warm-, neutral- and coolwhite version. They offer 36 individually addressable LED pixels per meter and a very dense LED arrangement. Per pixel 10 COB LEDs are used, so 360 LED/m, which ensures an absolutely homogeneous illumination even in small aluminum profiles, such as our E12.
The strip uses WS2811 IC's and an LED array for 24V power supply, which allows larger LED projects without new power supply. Single-sided fed up to 5m LED tape in a row are possible, double-sided fed even up to 10m.
> Video example of the LK133 Pixel COB stripe
Available variants
- 5m-Roll IP20 no water protection in 2500, 3000, 4000 & 6000K, incl. 10cm connection cable
Notes on accessories:
To operate 5m (1 roll) of LED strips, a 24V power supply with min. 60 Watt is required. 5m x 11W/m + 10% safety = 60 Watt.
A corresponding pixel LED controller is required to control the LEDs.
You can find answers to frequently asked questions in our FAQ.
Properties "Digital white COB LED strip WS2811 - 24V - 36 Pixel/m | 6000K cool white"
| Brightness lm/m: | 700 |
|---|---|
| IP protection: | IP20 |
| Pixel/m: | 36 |
| Power: | 11 |
| Seperatable every (cm): | 8,3 cm |
| Strip width in mm: | 10 |
| Voltage: | 24V |
| LED/m: | 360, COB |
Data according to manufacturer. Errors and changes reserved.
Manufacturer
LED-Studien GmbH
Mühlenweg 15
04451 Panitzsch
info@led-studien.de
datasheet
Video
Beispielvideo:
Skip product gallery
Power supply
Power supply HLG 24V - 5.0A - 120 Watt, extremely quiet
€59.00*
Switching power supply Meanwell HLG-120-24, 24 Volt, 5 Ampere, 120W
Overload protection by current limitation, auto recovery
protected against short circuit, overload, overvoltage
built-in PFC circuit
for indoor and outdoor use (IP65)
adjustable output voltage
adjustable current limitation
Technical data:
Model
HLG-120-24
Voltage
24V
Maximum power
120W
Current
5A
Adjustable voltage range
22 ~ 27V
Overcurrent protection
95...108%
Inrush current, max.
65A
Voltage input
90...264V AC (47...63Hz), 127...370V DC
Power factor
0,95
Working temperature
-40...+70°C
Dimensions
2220x68x38.8mm (LxWxH)
Weight
1,120g
Product number:
LED1134
Skip product gallery
Recommended driver
Artnet LED Pixel-Controller for up to 2.720 Pixel
€290.00*
The drivers for digital LED strips are specially designed to control as many RGB pixels as possible individually.With the LK99, up to 2,720 pixels are possible, divided into 4 channels with 680 RGB pixels each. This corresponds to a total of 16 DMX universes, which are transmitted via LAN/ArtNet. The 4 pixel outputs can be loaded with max. 7 amps per channel. For larger installations, the pixels can and should be powered separately. The controller then supplies only the data signal (DATA). Pixels with and without CLOCK signal (CLK) can be controlled. Pixel types with CLK are e.g. WS2801 or APA102. The controller can be controlled via ArtNet and offers an additional DMX-OUT port with 512 channels on the output side. For configuration, the controller has an integrated web interface as an alternative to direct input on the display. The configuration options are very extensive: selection of pixel type and color sequence (RGB, RGB, GRB etc.) flexible addressing (DMX-Universe and start address individually for each of the 4 outputs) number of pixels to control per channel (0-680 pixels - e.g. to save DMX universes) number of zero pixels to skip first unused pixels in an installation Zig-zag or backward addressing of pixels for matrix applications Brightness limitation per channel In addition, the controller offers a test mode to test the installation with various effects (Chase, Dots, Rainbow, ...) and static programs (all pixels red, all pixels white, ...) even without an applied ArtNet signal. The speed of the effects can be varied.
Technical data:
Item no.
LK99
Output spots
4 x 7 Ampere (Multi SPI)
Controllable pixels
4 x 680 = 2,720
Controllable ICs
WS2801, 2803, 2811, 2812, 2813, 2815
SK6812 (RGBW)
TM1803, 1804, 1809, 1812, 1814 (RGBW)
UCS1903, 1909, 1912, 2903, 2909, 2912, 5603UCS6909, 6912 9812, 2904 (RGBW), 8904 (RGBW)LPD6803, 1101, 8803, 8806
TLS3001, 3002
APA102
P9813
Voltage input
5 - 24VDC
DMX outputs
1 x 512 Channels
Dimensions
L166×W110×H31(mm)
Weight
510g
Product number:
LK99
Artnet LED Pixel driver for up to 5,440 pixels
€400.00*
The drivers for digital LED strips are specially designed to control as many RGB pixels as possible individually.
With the LK63, up to 5.440 pixels are possible, divided into 16 channels with 340 RGB pixels each. This corresponds to a total of 32 DMX universes, which are transmitted via LAN/ArtNet.
The 16 pixel outputs can be loaded with max. 3 amps per channel. For larger installations, the pixels can and should be powered separately. The controller then supplies only the data signal (DATA). Pixels with and without CLOCK signal (CLK) can be controlled. Pixel types with CLK are e.g. WS2801 or APA102. The controller can be controlled via ArtNet and offers 2 additional DMX-OUT ports with 512 channels each. For configuration, the controller has an integrated web interface as an alternative to direct input on the display. The configuration options are very extensive: selection of pixel type and color sequence (RGB, RGB, GRB etc.) flexible addressing (DMX-Universe and start address individually for each of the 4 outputs) number of pixels to control per channel (0-340 pixels - e.g. to save DMX universes) number of zero pixels to skip first unused pixels in an installation Zig-zag or backward addressing of pixels for matrix applications
Brightness limitation per channel
In addition, the controller offers a test mode to test the installation with various effects (Chase, Dots, Rainbow, ...) and static programs (all pixels red, all pixels white, ...) even without an applied ArtNet signal. The speed of the effects can be varied.
Technical data:
Item no.
LK63
Output spots
16 x 3 Ampere (Multi SPI)
Controllable pixels
16 x 340 = 5,440
Controllable ICs
WS2801, 2803, 2811, 2812, 2813, 2815
SK6812 (RGBW)
TM1803, 1804, 1809, 1812, 1814 (RGBW)
UCS1903, 1909, 1912, 2903, 2909, 2912, 5603UCS6909, 6912 9812, 2904 (RGBW), 8904 (RGBW)LPD6803, 1101, 8803, 8806
TLS3001, 3002
APA102
P9813
Voltage input
5 - 24VDC
DMX outputs
2 x 512 Channels
Dimensions
L258×W145×H41(mm)
Weight
1,100g
Product number:
LK63
SP636E Standalone LED pixel controller with app control for waterflow effects (white strips)
€35.00*
The SP636E is a standalone pixel controller specially designed for white LED strips. Its special feature is the various power-on effects, i.e. when the light is switched on, e.g. via a normal light switch, short animations/running lights are played before the light shines at full brightness (waterflow or running water effect). The effects and brightness levels are configured using a dedicated app. 4 different switch-on effects are available. There are also 10 other digital effects that can be played permanently. The controller offers 1 output for up to 1,800 pixels and operates in the 5-24VDC range. Various pixel types are supported for pure white pixels: WS2811 / 12 / 13 / 15 SK6812 SM16703 FW1934A The matching app “BanlanX” is available free of charge for IOS and Android.
Setting up the controller is intuitive and can be done in just a few minutes. The controller is controlled via Bluetooth. A small remote control for the most important functions is available as an option.
Screenshots of the App:
The scope of delivery includes:
1 x Pixel LED driver SP636E
1 x 3-pin connection cable for LED strips
1 x mini screwdriver
Supported LED types:WS2811 / 12 / 13 / 15 SK6812 SM16703FW1934A
FAQ:
Does the driver require an existing WLAN?
No, the controller is addressed directly via Bluetooth.Can the controller also control colored RGB LEDs? No, the SP636E can only be used for pure white pixel LED strips. Can the controller also be used with normal white LED strips (no pixel)? No, pixel LED strips (e.g. WS2811) are required. Normal LED strips will not light up on the controller and of course will not show any animations.
Can multiple drivers be used simultaneously in the app?
Yes, the app can manage multiple drivers at the same time. You can switch between the drivers and change the settings for each. In addition, the individual drivers can be switched on and off directly. However, there is no direct synchronization and each driver must be set accordingly for itself.
Does the app have to be active for the animations to run?
No. The app is only needed for the setup. You can close the app afterwards and also turn off the smartphone, for example. The SP636E will continue to play effects.
Does the driver keep its settings when it no longer receives power?
Yes, the driver can simply be disconnected from the mains. When power is applied again, it will start with the previously set animation. All settings will be kept.Can the SP636E also control LED matrices?
No. The SP636E does not currently offer any functions for LED matrices. It is only intended for LED pixel strips and corresponding chases.
Technical data:
Input: 5-24V DC, GND
Output: VCC, Data, GND
current consumption: 1-10mA
up to 1800 pixels depending on IC type
ambient temperature: -20°C - +60°C
dimensions: 78x56x20mm
Product number:
LK148
SP108E LED Pixel Controller with App control
€29.00*
The SP108 can drive up to 2,048 pixels and many different pixel types: WS2801, WS2811, WS2812, SK6812, APA102 and many more.
The suitable app "LED Shop" is available for free for IOS and Android and offers 180 different chase effects as well as precisely adjustable single colors. Speed and brightness can be changed at any time. A handy feature is that you can choose your favorites from the 180 effects and then quickly select them.
Setting up the driver is quite intuitive and done in a few minutes. The driver works in the 2.4 GHz WLAN and can be accessed directly via the smartphone as well as integrated into the home WLAN.
Screenshots of the App:
The scope of delivery includes:
1 x LED driver SP108E
1 x 3-pin connection cable for LED strips
1 x mini screwdriver
Supported LED types:
WS2801, WS2811, WS2812, WS2815
SK6812, SK6812_RGBW, SK9822
APA102, APA105
TM1804, TM1814, TM1913, TM1914, TX1812, TX1813
LPD6803, LPD8806
P9813, P943S, P9411, P9412, P9413, P9414
GS8206, GS8208
SM16703, UCS1903, INK1003, DMX512
FAQ:
Does the driver require an existing WLAN?
No, the driver can also be controlled directly with the smartphone (AP mode) and offers its own WLAN access point ("SP108E_xxx") for this purpose. If a WLAN is available, the driver can alternatively be integrated into it (STA mode), so that the WLAN does not always have to be changed to operate the driver.
Can multiple drivers be used simultaneously in the app?
Yes, the app can manage multiple drivers at the same time. You can switch between the drivers and change the settings for each. In addition, the individual drivers can be switched on and off directly. However, there is no direct synchronization and each driver must be set accordingly for itself.
Does the app have to be active for the animations to run?
No. The app is only needed for the setup. You can close the app afterwards and also turn off the smartphone, for example. The SP108 will continue to play effects.
Does the driver keep its settings when it no longer receives power?
Yes, the driver can simply be disconnected from the mains. When power is applied again, it will start with the previously set animation. All settings will be kept.
How can the white LEDs be used, e.g. with a SK6812_RGBW?
The app has a separate control for white LEDs (e.g. for SK6812_RGBW pixel strips). This can be used to set the proportion of white LEDs and then, in the case of effects, the white LEDs are taken into account accordingly, so that the colors are generally desaturated. In the effects section of the app, the SOLID setting can then also be used to activate a permanently white, high-quality light, e.g. for lighting tasks, if required.
Can the SP108 also control LED matrices?
A number of pixels and a number of segments can be set in the setup. For example, for an 8 x 8 matrix then 8 pixels and 8 segments. This is taken into account in the effects, but in most matrices the pixels are connected in a snake shape as a long line and this is unfortunately not taken into account by the SP108. Therefore the effects are not displayed as desired on the matrix, but every 2nd row of the matrix shows the effect quasi upside down. We hope for a technical improvement here soon.
Technical data:
Input: 5-24V DC, GND
Output: VCC, GND, Data, Clock
current consumption: approx. 90mA
up to 2.048 pixels, max. 300 pixel per line
ambient temperature: -20°C - +60°C
dimensions: 80x41x20mm
Weight: 40g
Product number:
LK126
Skip product gallery
Aluprofile
2m LED profile EL12
€17.40*
The small E12 LED corner profile has a very unobtrusive appearance thanks to its slim and flat design. It is mainly used indoors. The groove of the profile can hold LED strips up to 20 mm wide. This aluminum profile also ensures improved heat dissipation from the LED strips, which increases their service life. Please note that due to the compact design of the profile, LED strips with less than 180 LEDs/m will show the first LED dots in the profile cover. Use COB LED strips if necessary. Technical data:
Width: 17 mm
Height: 8 mm
Length: 10 cm sample
Width inside for LED strips: 12 mm
Other mounting options and accessories for line lights
If you want to realize long line lights, pendant lights or a hidden cable routing with this profile, choose the matching mounting rail PL10 with corresponding accessories.
The mounting rail is available in silver, black & white.
Further are available:
Rail connectors straight and angled
Cable suspensions
Mounting springs for fastening in drywall
Technical data:
Width: 17 mm
Height: 8 mm
Width inside for LED strips: 12.2 mm
Product number:
AL53bund
2m LED-Top-profile PL2
€17.00*
The LED top profile PL2 looks very inconspicuous due to its narrow and design. It is mainly used for indoor applications. The groove of the profile can hold up to 12 mm wide LED strips. In addition, this aluminum profile provides heat dissipation from the LED strips, which increases their service life.Technical data:
Width: 16.8 mm
Height: 13.1 mmLength: 2m
Width inside for LED strips: 12.4 mm
Other mounting options and accessories for line lights
If you want to realize long line lights, pendant lights or a hidden cable routing with this profile, choose the matching mounting rail PL10 with corresponding accessories.
The mounting rail is available in silver, black & white.
Further are available:
Rail connectors straight and angled
Cable suspensions
Mounting springs for fastening in drywall
Product number:
AL24bund
2m LED corner profile 45° W12
€17.40*
The small LED corner profile W12 is very unobtrusive thanks to its compact design and aligns the LEDs at 45°, e.g. to illuminate larger areas from a corner. It is mainly used indoors. The profile can hold LED strips up to 12 mm wide. This aluminum profile also ensures improved heat dissipation from the LED strips, which increases their service life. Please note that due to the compact design of the profile, LED strips with less than 180 LEDs/m will show the first LED dots in the profile cover. Use COB LED strips if necessary.
Technical data:
Width: 16 mm
Height: 16 mmLength: 2 m
Width inside for LED strips: 12.8 mm
Product number:
AL46bund