LED tape digital WS2811 - 60 RGB-LEDs/m - IP67 - 12V

The SP801E is a standalone pixel controller that can be controlled via its own "BanlanX" app as well as via WiFi using ArtNet (e.g. via JINX!). It provides 4 outputs of up to 1,024 pixels each, for a total of up to 4,096 pixels. Many common pixel types are supported:WS2811 / 12 / 13 / 15 TM1812 SK6812 (not RGBW!) UCS1903 GS8206 The matching app "BanlanX" is available for free for IOS and Android and offers more than 100 different chaser effects as well as precisely adjustable individual colors. Speed and brightness can be changed at any time.  Setting up the controller is intuitive and can be done in minutes. The controller operates on 2.4 GHz WLAN and can be accessed directly from your smartphone or integrated into your home WLAN. Screenshots of the App: The scope of delivery includes: 1 x Pixel LED driver SP801E 1 x 3-pin connection cable for LED strips 1 x mini screwdriver Supported LED types:WS2811 / 12 / 13 / 15  TM1812  SK6812 (not RGBW!)  UCS1903  GS8206  FAQ: Does the driver require an existing WLAN? No, the driver can also be controlled directly with the smartphone (AP mode) and offers its own WLAN access point ("SP108E_xxx") for this purpose. If a WLAN is available, the driver can alternatively be integrated into it (STA mode), so that the WLAN does not always have to be changed to operate the driver. Can multiple drivers be used simultaneously in the app? Yes, the app can manage multiple drivers at the same time. You can switch between the drivers and change the settings for each. In addition, the individual drivers can be switched on and off directly. However, there is no direct synchronization and each driver must be set accordingly for itself.  Does the app have to be active for the animations to run? No. The app is only needed for the setup. You can close the app afterwards and also turn off the smartphone, for example. The SP108 will continue to play effects. Does the driver keep its settings when it no longer receives power? Yes, the driver can simply be disconnected from the mains. When power is applied again, it will start with the previously set animation. All settings will be kept. How can the white LEDs be used, e.g. with a SK6812_RGBW? It's not possible to operate the white LEDs of an RGBW Pixel strip like SK6812. Use the alternative SP108E to control also the white LEDs in RGBW setups. Can the SP801 also control LED matrices? The SP801E offers a very flexible matrix setup.  Technical data: Input: 5-24V DC, GND Output: VCC, GND, Data, Clock current consumption: 25-130mA up to 4.096 pixels depending on IC type ambient temperature: -20°C - +60°C dimensions: 80x41x20mm Weight: 40g

The LK142 Staircase Effect Controller allows the control of staircase lighting from 8 - 32 steps. It offers a total of 32 outputs, e.g. for LED strips or profiles in the range of 5-24VDC, 1A. For example, our standard LED strips as well as the new free-cut COB LED strips can be controlled flexibly. Controlled by pushbuttons or motion detectors above and below the stairs, the steps can be illuminated step by step with great effect. Depending on the activation, the effect runs from bottom to top or from top to bottom. In addition, digital pixel LEDs can be integrated for a running light, e.g. in the handrail. Various effect modes and speed settings allow for flexible adjustment of the staircase effect.Benefits at a glance: Selective control of 8-32 steps with 5-24VDC, 1A Additional chaser effect, e.g. in the handrail, via pixel LED strips (12 color modes) 4 effect modes, 8 speeds Triggered by PIR motion sensors or push-buttons above and below the stairs Daylight sensor for twilight switching 2 controllers can be cascaded for large staircases with up to 64 steps Wiring diagram: Scope of delivery:Staircase effect controller 2 x PIR sensor 2 x extension cable (5m) for PIR sensor 1 x twilight sensor Technical data: Item-Nr. LK142 Output ports 32 x 5-24VDC, 1A step illumination2 x SPI pixel for running light Adressable pixel Up to 960 pixel Adressable pixel types WS2801, 2803, 2811, 2812, 2813, 2815TM1804, 1809, 1812, 1829, 1914AUCS1903, 1909, 1912, 2903, 2909, 2912UCS5909, 6912LPD6803, 1101, 8803, 8806GS8206, 8208GW6205P9813SK9822 Powersupply  5 - 24VDC (via ext. powersupply) Input ports2 x 5-24VDC voltage input2 x PIR motionsensor 2 x pushbutton (+ cascade option)1 x daylight sensor IP protection IP20 Dimensions L186×W86×H26(mm) Weight 520g

The drivers for digital LED strips are specially designed to control as many RGB pixels as possible individually.  With the LK63, up to 5.440 pixels are possible, divided into 16 channels with 340 RGB pixels each. This corresponds to a total of 32 DMX universes, which are transmitted via LAN/ArtNet.  The 16 pixel outputs can be loaded with max. 3 amps per channel. For larger installations, the pixels can and should be powered separately. The controller then supplies only the data signal (DATA).  Pixels with and without CLOCK signal (CLK) can be controlled. Pixel types with CLK are e.g. WS2801 or APA102.  The controller can be controlled via ArtNet and offers 2 additional DMX-OUT ports with 512 channels each. For configuration, the controller has an integrated web interface as an alternative to direct input on the display.  The configuration options are very extensive:  selection of pixel type and color sequence (RGB, RGB, GRB etc.)  flexible addressing (DMX-Universe and start address individually for each of the 4 outputs) number of pixels to control per channel (0-340 pixels - e.g. to save DMX universes)  number of zero pixels to skip first unused pixels in an installation  Zig-zag or backward addressing of pixels for matrix applications  Brightness limitation per channel  In addition, the controller offers a test mode to test the installation with various effects (Chase, Dots, Rainbow, ...) and static programs (all pixels red, all pixels white, ...) even without an applied ArtNet signal. The speed of the effects can be varied. Technical data: Item no. LK63 Output spots 16 x 3 Ampere (Multi SPI) Controllable pixels 16 x 340 = 5,440 Controllable ICs WS2801, 2803, 2811, 2812, 2813, 2815 SK6812 (RGBW) TM1803, 1804, 1809, 1812, 1814 (RGBW) UCS1903, 1909, 1912, 2903, 2909, 2912, 5603UCS6909, 6912 9812, 2904 (RGBW), 8904 (RGBW)LPD6803, 1101, 8803, 8806 TLS3001, 3002 APA102 P9813 Voltage input  5 - 24VDC DMX outputs 2 x 512 Channels Dimensions L258×W145×H41(mm) Weight 1,100g

The drivers for digital LED strips are specially designed to control as many RGB pixels as possible individually.With the LK99, up to 2,720 pixels are possible, divided into 4 channels with 680 RGB pixels each. This corresponds to a total of 16 DMX universes, which are transmitted via LAN/ArtNet. The 4 pixel outputs can be loaded with max. 7 amps per channel. For larger installations, the pixels can and should be powered separately. The controller then supplies only the data signal (DATA). Pixels with and without CLOCK signal (CLK) can be controlled. Pixel types with CLK are e.g. WS2801 or APA102. The controller can be controlled via ArtNet and offers an additional DMX-OUT port with 512 channels on the output side. For configuration, the controller has an integrated web interface as an alternative to direct input on the display. The configuration options are very extensive: selection of pixel type and color sequence (RGB, RGB, GRB etc.) flexible addressing (DMX-Universe and start address individually for each of the 4 outputs) number of pixels to control per channel (0-680 pixels - e.g. to save DMX universes) number of zero pixels to skip first unused pixels in an installation Zig-zag or backward addressing of pixels for matrix applications Brightness limitation per channel In addition, the controller offers a test mode to test the installation with various effects (Chase, Dots, Rainbow, ...) and static programs (all pixels red, all pixels white, ...) even without an applied ArtNet signal. The speed of the effects can be varied. Technical data: Item no. LK99 Output spots 4 x 7 Ampere (Multi SPI) Controllable pixels 4 x 680 = 2,720 Controllable ICs WS2801, 2803, 2811, 2812, 2813, 2815 SK6812 (RGBW) TM1803, 1804, 1809, 1812, 1814 (RGBW) UCS1903, 1909, 1912, 2903, 2909, 2912, 5603UCS6909, 6912 9812, 2904 (RGBW), 8904 (RGBW)LPD6803, 1101, 8803, 8806 TLS3001, 3002 APA102 P9813 Voltage input  5 - 24VDC DMX outputs 1 x 512 Channels Dimensions L166×W110×H31(mm) Weight 510g

Meanwell switching power supply HLG-240, 12V / 16A / 192W Overload protection by current limitation, auto recovery protected against short circuit, overload, overvoltage built-in PFC circuit for indoor and outdoor use (IP65) adjustable output voltage adjustable current limitation Note on the connection of LED drivers The HLG-240-12 offers a lot of power and therefore a high current of up to 12.5 amps. If possible, use both voltage inputs on all drivers with dual voltage inputs (++--). All larger drivers usually have dual voltage inputs. It is best to order two 3-way WAGO distributors so that you can split the +/- output cables of the HLG-150 into 2 cables each, which you then run in parallel to the driver inputs. Alternatively, you can use a driver Y-connection cable in combination with luster terminals. Technical data:  Model HLG-240-12  Voltage 12V  Maximum power 192W  Current 16A  Adjustable voltage range 6 ~ 12V  Overcurrent protection 95...108%  Inrush current, max. 75A  Voltage input 90...264V AC (47...63Hz), 127...370V DC  Power factor 0,95  Working temperature -40...+70°C  Dimensions 244.2x68x38.8mm (LxWxH)  Weight 1,300g