Mini LED dimmer for aluminium profiles - Touch | 12-24V | 1x3A

Free Cut! The LED strip can be divided at any pointLED type: COB - no single LEDs visibleBeam angle: 170°Brightness: 1,500 lm/mColor rendering: High CRI>90Voltage: 24 VoltPower: 15 Watt/m Free CutUnlike normal LED strips, Free Cut LED strips can be cut at any point. While normal LED strips have fixed division marks (e.g. every 5cm) and a cut between the marks would destroy the entire 5cm segment, there are no division marks with Free-Cut LED strips. It can be cut at any point and the Free-Cut strip will shine homogeneously right up to the cut point. This enables perfect light lines, e.g. for shelf lighting Staircase lighting any type of insert or plaster-in profile that needs to be installed to the exact length COB LED structureThe strip is manufactured in a COB design in which no individual LEDs are visible! A continuously bright, uniform light strip is produced.   This has advantages for various applications: Homogeneous line light, even in very flat aluminum profiles. Continuous, narrow accent or orientation light Absolutely uniform indirect lighting at very short distances The COB LED-Strips are also very efficient - approx. 100 lumens / watt - and can be processed just as flexibly as normal LED strips. The free-cut design allows the length to be adjusted to any desired dimension and the double-sided adhesive tape on the back makes the COB LED strips very easy to install. The continuous light effect without visible individual LEDs in the COB LED-Strip is achieved by a new process. With white LEDs, the light has always been generated by a converting phosphor layer. Now, instead of applying a separate, tiny phosphor layer to each LED chip - as it is usually the case - COB LED-Strips cover the entire 5m strip in one piece with a continuous phosphor. The result is a uniformly homogeneous band of light, as in color, so in brightness. Available Variants Meter goods IP20, connection cable optional All variants have a 3M adhesive tape on the back for mounting, can be divided at any point and are available in various color temperatures (e.g. 3,000K warm white). Notes on accessories: To operate 5m of LED strips, a 24V power supply with min. 75 Watt is required. 5m x 15W/m = 75 Watt. For brightness control of 5m a driver with min. 3,2 Ampere is needed. 75W / 24V = 3,2 Ampere. Frequently asked questions:   Can COB LED-Strips be used like normal LED Strips? Yes. COB-LED-Strips can be laid, cut and connected just as flexibly as normal LED-Strips. The solder contacts for connecting cables are also exposed.   What is the height of the COB LED-Strips? Only 1.5mm. COB LED-Strips are not significantly higher than normal LED strips and therefore fit, for example, in all standard aluminum profiles. The IP67 versions have the typical height of 4mm due to the surrounding silicone tube.   Does the phosphor coating reduce the lifetime of the LEDs? No. COB technology has been used for many years in numerous high-power LED modules (up to 100 Watt output), where the temperature input into the phosphor coating is immensely high. There is no known reduction in lifetime here.    You can find more answers to frequently asked questions about LED strips in our FAQ.  

48V enable particularly long LED lines20m with feed on one side40m with feed on both sides Brightness: 800 lm/m Color rendering: High CRI>90 Power: 8 Watt/mWidth: 10mmDivisible every 1.67cm 48V LED stripsLED strips with a 48V design enable particularly long LED lines as the typical voltage and brightness drop is significantly reduced. Lengths of up to 20m are possible with a single-sided voltage supply. If fed in on both sides (or in the middle), a total length of 40m is even possible.Another advantage of this LED strip is its very narrow pitch of just 1.67 cm. This means that the LED line can be adapted to almost any situation. With 120 LEDs/m, the LED density is sufficiently high so that many aluminum profiles (from 10 mm installation depth) can be used for a perfectly homogeneous light line without spot formation.With CRI>90, the LED strip also achieves excellent color quality, even for demanding requirements.48V LED strips are the perfect solution for all installations where parallel cable routing is difficult or impossible. Typical examples areLong LED lines in corridors, stairwells, etc.Façade lighting (observe IP protection)Indirect lighting with very filigree light coves / stucco moldings Available variants By the meter IP20, connection cable optional All versions have a 3M adhesive tape on the back for mounting, can be split at any point and are available in various color temperatures (e.g. 3,000K warm white). Notes on accessories: A 48V power supply unit with at least 160 watts is required to operate 20m LED strips. 20m x 8W/m = 160 watts. A controller with at least 3.4 amps is required to control the brightness of the 20m. 160W / 48V = 3.4 amps. Frequently asked questions:   Is it safe to install 48V LED strips? Yes. Just like 24V or 12V, 48V belongs to the low voltage range and can be installed by anyone.   Are there any disadvantages of 48V LED strips compared to the familiar 24V LED strips? There is currently still a very limited selection of LED strips and LED controllers in the 48V range. This means that you have to make do with a few options for control.   Are 48V LED strips particularly efficient and generate less heat than 24V LED strips, for example? No. The efficiency and heat development are comparable. We therefore also recommend aluminum profiles for heat dissipation of the LEDs for 48V LED strips.    Further answers to frequently asked questions about LED strips can be found in our FAQ.    

48V enable particularly long LED lines20m with feed on one side40m with feed on both sides Brightness: 800 lm/m Color rendering: High CRI>90 Power: 8 Watt/mWidth: 10mmDivisible every 1.67cm 48V LED stripsLED strips with a 48V design enable particularly long LED lines as the typical voltage and brightness drop is significantly reduced. Lengths of up to 20m are possible with a single-sided voltage supply. If fed in on both sides (or in the middle), a total length of 40m is even possible.Another advantage of this LED strip is its very narrow pitch of just 1.67 cm. This means that the LED line can be adapted to almost any situation. With 120 LEDs/m, the LED density is sufficiently high so that many aluminum profiles (from 10 mm installation depth) can be used for a perfectly homogeneous light line without spot formation.With CRI>90, the LED strip also achieves excellent color quality, even for demanding requirements.48V LED strips are the perfect solution for all installations where parallel cable routing is difficult or impossible. Typical examples areLong LED lines in corridors, stairwells, etc.Façade lighting (observe IP protection)Indirect lighting with very filigree light coves / stucco moldings Available variants By the meter IP20, connection cable optional All versions have a 3M adhesive tape on the back for mounting, can be split at any point and are available in various color temperatures (e.g. 3,000K warm white). Notes on accessories: A 48V power supply unit with at least 160 watts is required to operate 20m LED strips. 20m x 8W/m = 160 watts. A controller with at least 3.4 amps is required to control the brightness of the 20m. 160W / 48V = 3.4 amps. Frequently asked questions:   Is it safe to install 48V LED strips? Yes. Just like 24V or 12V, 48V belongs to the low voltage range and can be installed by anyone.   Are there any disadvantages of 48V LED strips compared to the familiar 24V LED strips? There is currently still a very limited selection of LED strips and LED controllers in the 48V range. This means that you have to make do with a few options for control.   Are 48V LED strips particularly efficient and generate less heat than 24V LED strips, for example? No. The efficiency and heat development are comparable. We therefore also recommend aluminum profiles for heat dissipation of the LEDs for 48V LED strips.    Further answers to frequently asked questions about LED strips can be found in our FAQ.    

The LED micro profile PL1 looks very inconspicuous due to its particularly narrow and flat design. It is mainly used indoors. The groove of the profile can hold up to 12 mm wide LED strips. In addition, this aluminum profile provides improved heat dissipation from the LED strips, which increases their service life. Technical data: Width: 16.8 mm Height: 6 mm Length: 2 m Width inside for LED strips: 12.4 mm  Other mounting options and accessories for line lights If you want to realize long line lights, pendant lights or a hidden cable routing with this profile, choose the matching mounting rail PL10 with corresponding accessories. The mounting rail is available in silver, black & white. Further are available: Rail connectors straight and angled Cable suspensions Mounting springs for fastening in drywall

The flexible silicone insert covers are ideal if LED lighting is to be integrated into grooves, e.g. in an acoustic panel. The LED strip is glued into the groove at the bottom (aluminum profiles should be used from 5W/m) and then the silicone insert cover is pressed into the groove from above.The flexible silicone means that curves are also possible and the opal structure of the cover effectively blends LED points (from 120 LEDs/m). The result is a uniform, homogeneous line of light.Please note that this concept is not suitable for high-power LED strips, as there is insufficient cooling effect. Only LED strips with max. 5W/m should be used without an aluminum profile. Slightly higher wattages are also possible with flat aluminum profiles. Technical data: Width: 15 mm Height: 10 mmRequired groove width: 9-10 mmRequired groove depth: min. 10 mm Max. width for LED strips: 10 mmWe recommend a pressure roller for gluing and lightly pressing on the LED strips.

The flexible silicone insert covers are ideal if LED lighting is to be integrated into grooves, e.g. in an acoustic panel. The LED strip is glued into the groove at the bottom (aluminum profiles should be used from 5W/m) and then the silicone insert cover is pressed into the groove from above.The flexible silicone means that curves are also possible and the opal structure of the cover effectively blends LED points (from 120 LEDs/m). The result is a uniform, homogeneous line of light.Please note that this concept is not suitable for high-power LED strips, as there is insufficient cooling effect. Only LED strips with max. 5W/m should be used without an aluminum profile. Slightly higher wattages are also possible with flat aluminum profiles. Technical data: Width: 20 mm Height: 10 mmRequired groove width: 13-15 mmRequired groove depth: min. 10 mm Max. width for LED strips: 15 mmWe recommend a pressure roller for gluing and lightly pressing on the LED strips.

The SP01 LED tensioning system allows LED light lines to be freely positioned in the room. This is made possible by 2 wall brackets, between which a 15 mm wide steel strip is stretched. This steel strip can then accommodate an LED strip and shine freely into the room, onto the ceiling or the wall. Direct and indirect lighting solutions with comparatively little installation effort are thus possible. Thanks to the ball joint in the wall brackets, angled lines with angles of 0 - 90° are also possible. The video in the video tab shows many examples. For installation, the supply cable for the LED strip is fed through the wall bracket, then the bracket is screwed on and tensioned. The LED strip is then fully bonded to the steel strip. The result is a filigree line of light without visible cable routing. Technical data: Max. Length: 10 m Wall bracket diameter: 90 mm Wall bracket structure: 113 - 143 mm  Max. Width for LED strips: 15 mm

The B12 floor profile is suitable for installing LED light lines in the floor. Thanks to its sturdy construction and 1.5 mm thick opal cover, it is tread-resistant and can also be rolled over.  The thick opal cover also ensures good mixing of the LEDs, so that absolutely homogeneous light lines are created from an LED density of 120 LEDs/m. The B12 floor profile is always supplied with an opal cover. Technical data: Width: 16 mm Length: 2 m Height: 12.7 mm (incl. opal cover)Internal width for LED strips: 13.2 mm Note: The B12 floor profile offers a contact surface of 13.2 mm. However, please note the upper narrowing caused by the support surface for the opal cover. This narrowing is only 10mm wide, which must be taken into account when gluing in the LED strips from above. A typical 12mm wide LED strip can be easily inserted at an angle, but if it is an LED strip in a 12mm wide IP67 silicone tube, it can only be inserted from the side. We recommend a pressure roller for gluing in and lightly pressing on the LED strips.

Barrel plug for DC power supply (or simmilar) with screw terminals for connection cables up to max. 2.5mm².Max. current: 3A  

Barrel socket as counterpart for DC connection power supplies or similar with spring-loaded terminals for connection cables up to max. 2.5mm².Max. current: 3A