DALI wall-mounted touch interface | 4 zones

Multifunctional LED controller with 2 x 10A output power for various control types:DALI DT6 (1 address)0/1-10V PushDim (230V)230V PhaseCut (TRIAC) This means that the controller can be used in a wide variety of setups and, for example, integrate an installation with LED strips into existing control concepts. With an output power of 2 x 10 amps, it is also well equipped for large LED installations. Wiring examples 0/1-10V DALI 230V PushDim 230V PhaseCut Scope of delivery: 1 x driver LK145 Technical data Outputs: 2Voltage: 12V-36V DCPower: Power connection via external switching power supply (not included)Load: 10A per outputInput: (V+/ground, PhaseCut, DALI in / PushDim, 0/1-10V)Output: (2 x LED)IP class: IP 20Ambient temperature: -20°C - +50°CDimensions: LxBxH 170x54x28mm Note: The controller has double voltage inputs (++--). If the connected load is high (> 200 watts), use our special Y connection cables to split the current load between both inputs. The two large power supply units HLG-480 and HLG-600 already have dual voltage outputs so that both voltage inputs of the controller can be used directly. Dimensional drawings:

LED controller for DALI and convenient PUSH DIM operation. In addition to DALI functionality, this controller also allows extensive PUSH DIM control, so that, for example, when using appropriate CCT LED strips, on/off, dimming and changing the color temperature are possible with just one light switch.DALI mode Since the driver is capable of DT8, it can be operated in different modes: RGB(W) RGB+CCT CCT tunablewhite with 2 outputs each for warm white & cool white White channels with 4 parallel outputs XY coordinates for color control The mode is selected via the small display on the driver, as is the setting of the DALI address. The address can also be assigned automatically by the DALI master. Wiring for RGBW and XY mode   Wiring for CCT mode   Wiring for white mode PUSH DIM mode The driver also offers a very practical PUSH DIM mode. Instead of the DALI signal, a simple pushbutton is then connected. This offers the following functions: Single channel mode: Short press > On / Off | Long press > Dimming CCT tunable white mode:Short press > On / Off | Long press > Dim | Double press > Switch to CCT mode > Long press changes color temperature RGB mode: Short press > On / Off | Long press > Dim | Double press > Change to RGB color mode > Long press changes color  I.e. it can realize here, for example, with only one light switch on the wall a convenient control of brightness, color temperature (or color) and on / off.   Wiring for PUSH DIM mode (in the example as CCT setup) Scope of delivery: 1x Receiver LK124pro Technical data: Channels: 5Voltage: 12V-36V DCPower: Power connection via external switching power supply (not included)Load: 4A per output port, 1500Hz PWMInput: (V+/ground, DALI or PUSH DIM in)Output: (4 x LED channel, V+, DALI out)IP class: IP 20Ambient temperature: -20°C - +50°CDimensions: LxWxH 170x54x28mm ​Note: The driver has double voltage inputs (++--). For high connected load (> 200 Watt), use our special connection cables for high connected loads (> 200 watts) in order to divide the current load between the two inputs. The large power supplies HLG-480 and HLG-600 already have double voltage outputs, so that both voltage inputs of the driver can be used directly here.  Dimensional drawings:

LED controller for DALI and PUSHDIM operation with 4 x 4 Amp outputs. DALI mode Since the driver is capable of DT8, it can be operated in different modes: RGB(W)  CCT tunablewhite with 2 outputs each for warm white & cool white XY coordinates for color control The mode is selected via the small display on the driver, as is the setting of the DALI address. The address can also be assigned automatically by the DALI master.DALI master functionThe controller can take over DALI master functions and therefore does not require a separate DALI master. Typical DALI functions such as assigning to groups and scenes, setting fade times, min. brightness level, power on behavior and much more can be carried out directly on the controller. Wiring example Scope of delivery: 1x Receiver LK124 Technical data: Channels: 4Voltage: 12V-36V DCPower: Power connection via external switching power supply (not included)Load: 4A per output portInput: (V+/ground, DALI or PUSH DIM in)Output: (4 x LED channel, V+, DALI out)IP class: IP 20Ambient temperature: -20°C - +50°CDimensions: LxWxH 170x54x28mm ​Note: The driver has double voltage inputs (++--). For high connected load (> 200 Watt), use our special connection cables for high connected loads (> 200 watts) in order to divide the current load between the two inputs. The large power supplies HLG-480 and HLG-600 already have double voltage outputs, so that both voltage inputs of the driver can be used directly here.  Dimensional drawings:

This DALI driver is designed for 4-channel LED applications and can therefore be used e.g. to control RGBW LED systems, but also for installations with adjustable color temperature (CCT) or to dim 4 independent zones with white LEDs.  Each of the 4 outputs can be loaded with 4A, which makes even very large installations feasible. The LED driver works with all known DALI drivers Scope of delivery: 1x Receiver LK87 Technical data: Channels: 4Voltage: 12V-36V DCPower: Power connection via external switching power supply (not included)Load: 4A per output portConnection: Input (V+/ground, DALI in) Output (4xLED channel, V+, DALI out, Power out)IP class: IP 20Dimensions: LxWxH 179x46x19mm Note: The driver has double voltage inputs (++--). For high connected load (> 200 Watt), use our special connection cables for high connected loads (> 200 watts) in order to divide the current load between the two inputs. The large power supplies HLG-480 and HLG-600 already have double voltage outputs, so that both voltage inputs of the driver can be used directly here. 

Power supply for the DALI bus. Input voltage range: 100-240VAC Output: 16VDC, max. 250mA Installation:   Technical data: Dimensions: